IP Aliasing with "IP"?
billy [email protected]
<PRE>Can I do something like this?
old way:
ifconfig eth1 192.168.101.1 netmask 255.255.255.0 up route add -net 192.168.101.0 netmask 255.255.255.0 eth1 ifconfig eth1:0 192.168.101.1 netmask 255.255.255.0 up route add -net 192.168.101.0 netmask 255.255.255.0 eth1:0
thanks
</PRE>
bert hubert [email protected]
<PRE>On Tue, Jan 30, 2001 at 05:50:01PM -0300, billy wrote:
><i>
</I>><i> Can I do something like this?
</I>><i>
</I>><i> old way:
</I>><i>
</I>><i> ifconfig eth1 192.168.101.1 netmask 255.255.255.0 up </I>><i> route add -net 192.168.101.0 netmask 255.255.255.0 eth1 </I>><i> ifconfig eth1:0 192.168.101.1 netmask 255.255.255.0 up </I>><i> route add -net 192.168.101.0 netmask 255.255.255.0 eth1:0 </I>
ip addr add dev eth0 192.168.101.1 etc etc should work
Signature · 6 lines
PowerDNS Versatile DNS Services Trilab The Technology People 'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet </PRE>
billy [email protected]
<PRE>On Tuesday 30 January 2001 17:51, you wrote:
><i> On Tue, Jan 30, 2001 at 05:50:01PM -0300, billy wrote:
</I>><i> > Can I do something like this?
</I>><i> >
</I>><i> > old way:
</I>><i> >
</I>><i> > ifconfig eth1 192.168.101.1 netmask 255.255.255.0 up </I>><i> > route add -net 192.168.101.0 netmask 255.255.255.0 eth1 </I>><i> > ifconfig eth1:0 192.168.101.1 netmask 255.255.255.0 up </I>><i> > route add -net 192.168.101.0 netmask 255.255.255.0 eth1:0 </I>><i>
</I>><i> ip addr add dev eth0 192.168.101.1 etc etc should work </I>
OK, but what about eth0:0, the alias ? if I do something like:
# ip addr add dev eth0:0 192.168.101.1 etc etc
I get an error:
cannot find device "eth0:0"
but I can create eth0:0 with ifconfig, but "ip link show" does not show me the interfaces, but with "ip route show" I see all of the eth0:x as only eth0.
# ip route show 200.51.164.128/29 dev eth0 proto kernel scope link src 200.51.164.131 192.168.101.0/24 dev eth0 proto kernel scope link src 192.168.101.1 192.168.102.0/24 dev eth0 proto kernel scope link src 192.168.102.1 127.0.0.0/8 dev lo scope link default via 200.51.164.134 dev eth0 #
is this ok? I haev to create the "virtual" interfaces with ifconfig or do I have a way with ip?
thanks billy
</PRE>
bert hubert [email protected]
<PRE>On Tue, Jan 30, 2001 at 06:08:00PM -0300, billy wrote:
><i> OK, but what about eth0:0, the alias ? if I do something like:
</I>
Those 0:0 names are just imagined by ifconfig :-) iproute2 reflects reality.
><i> is this ok? I haev to create the "virtual" interfaces with ifconfig or do I </I>><i> have a way with ip?
</I>
ip adds IP addresses to your physical interface - which is better than inventing 'new' interfaces.
Regards,
bert hubert
Signature · 6 lines
PowerDNS Versatile DNS Services Trilab The Technology People 'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet </PRE>
Arkadiusz Miskiewicz [email protected]
<PRE>On/Dnia Tue, Jan 30, 2001 at 06:08:00PM -0300, billy wrote/napisa³(a) ><i> > ip addr add dev eth0 192.168.101.1 etc etc should work
</I>><i> OK, but what about eth0:0, the alias ? if I do something like:
</I>><i> # ip addr add dev eth0:0 192.168.101.1 etc etc
</I>><i> I get an error:
</I>><i> cannot find device "eth0:0"
</I>[<A HREF="mailto:root@arm">root@arm</A> misiek]# ip addr add 1.1.1.1 dev eth0 label eth0:qpa [<A HREF="mailto:root@arm">root@arm</A> misiek]# ifconfig | grep qpa
eth0:qpa Link encap:Ethernet HWaddr 00:E0:7D:8A:4C:79
><i> but I can create eth0:0 with ifconfig, but "ip link show" does not show me </I>><i> the interfaces, but with "ip route show" I see all of the eth0:x as only eth0. </I>><i>
</I>><i> is this ok? I haev to create the "virtual" interfaces with ifconfig or do I </I>><i> have a way with ip?
</I>It's ok. Routing is to real device, not to so called ,,aliases''.
Signature · 5 lines
Arkadiusz Mi¶kiewicz, AM2-6BONE [ PLD GNU/Linux IPv6 ] <A HREF="http://www.t17.ds.pwr.wroc.pl/~misiek/ipv6/">http://www.t17.ds.pwr.wroc.pl/~misiek/ipv6/</A> [ enabled ] </PRE>